22 LR Meter results

Rangerwalker71

Rangerwalker71

New member
Hit the range this morning to test some 22 LR suppressors.
Once again here are the conditions:
71.8 F.
1263 EVL.
30.1 inHG,
Calm winds, with over cast skys.

Same B&K 2209 meter, 1.6m high, 1 meter to the left of weapons bore. Bore on line with mic.

Host weapon Browning Buckmark II with 4" barrel
22LR Aguila super Extra ammo:
Ballistics Information:

Muzzle Velocity: 1250 fps
Velocity Rating: High Velocity
Muzzle Energy: 139 ft. lbs.



Ammo stayed Sub-Sonic out of the 4" barrel.

Average 154.38 Non-Suppressed.
#1. 154.5
#2. 154
#3. 154.6
#4. 154.5
#5. 154.3

SAS Tolerance 22LR Suppressor
#1. 118.2
#2. 115.5
#3. 116.2
#4. 117.0
#5. 117.3

Average 116.84 suppressed with the SAS Tolerance


SICO Spectre II

#1. 121.1
#2. 116.5
#3. 114.3
#4. 117.7
#5. 117.4
5 Shot average 117.4



SICO SS Sparrow

#1. 133.4 FRP
#2. 117.8
#3. 119.2
#4. 116
#5. 117.2
5 shot average 120.7
Very repeatable FRP. I shot it 4 times, after waiting 5-7 minutes between each shot.

Surefire Ryder 22-A
#1. 130.2 FRP
#2. 125.3
#3. 122.0
#4. 124.5
#5. 124.5
Average 125.30

Again repeatable FFP.

Griffin Armament QD
#1. 128.5
#2. 116.9
#3. 115.8
#4. 116.1
#5. 119.6
5 shot average. 119.38

Hope this helps. Will try and get more range time when i can.

Thanks
Steve
RLTW
 
Last edited:

RangerWalker,

I'm trying to learn more about suppressors so I can make an informed decision when I am ready to purchase one - or two. Your information is great and a good comparison.

I do have some particular questions that I don't fully understand, so please forgive me if I sound dumb and inexperienced, because I am in regards to this subject.

(1) I assume suppressors specifically rated for 22 long rifle can also be used with any rimfire, such as a 22 mag or 17 HMR, correct?

(2) It appears (if I read your data correctly) that the SAS Tolerance gives the quietest and the most repeated level from one shot to another, specifically from the first shot to the others. Am I reading that correctly? If so, then I would assume the SAS Tolerance suppressor rated the best of all? Does this suppressor allow for taking it apart and cleaning?

(3) With the Sparrow, you mention "very repeatable FFP." What is FFP? It appears the Sparrow has a louder first shot and then the others subsequent shots settle down after that. Is that what is considered "first shot pop" that I have read in other posts, or is that a different subject?

I appreciate your thoughts.

 
Originally Posted By: 6mm06
RangerWalker,

I'm trying to learn more about suppressors so I can make an informed decision when I am ready to purchase one - or two. Your information is great and a good comparison.

I do have some particular questions that I don't fully understand, so please forgive me if I sound dumb and inexperienced, because I am in regards to this subject.

(1) I assume suppressors specifically rated for 22 long rifle can also be used with any rimfire, such as a 22 mag or 17 HMR, correct?

(2) It appears (if I read your data correctly) that the SAS Tolerance gives the quietest and the most repeated level from one shot to another, specifically from the first shot to the others. Am I reading that correctly? If so, then I would assume the SAS Tolerance suppressor rated the best of all? Does this suppressor allow for taking it apart and cleaning?

(3) With the Sparrow, you mention "very repeatable FFP." What is FFP? It appears the Sparrow has a louder first shot and then the others subsequent shots settle down after that. Is that what is considered "first shot pop" that I have read in other posts, or is that a different subject?

I appreciate your thoughts.




Most But not all. The only ones that are good for any rim fire are: SAS Tolerance, Spectre II, SS Sparrow, The Griffin is good for 22LR and 17HMR, SF is good for 22LR only.

Yes, The SAS is the most consistent across the board.
It is also user serviceable as well.
FRP is what i meant, First Round POP.
 

To touch on what RangerWalker said, the Tolerance from SAS is brand new from the ground up. It was designed especially to reduce FRP, accuracy and quiet. Its also SAS intro to the user serviceable world.

It can be had in grade 6 titanium, stainless for hard FA use or aluminum. The aluminum version baffels are hardcoat anodized to help in cleanup.

I've ran one awhile and they are super accurate. The milspec testing shows the notorious FRP on rimfire cans has been addressed and its extremely quiet.
 
Originally Posted By: 6mm06
RangerWalker,

I'm trying to learn more about suppressors so I can make an informed decision when I am ready to purchase one - or two. Your information is great and a good comparison.

I do have some particular questions that I don't fully understand, so please forgive me if I sound dumb and inexperienced, because I am in regards to this subject.

(1) I assume suppressors specifically rated for 22 long rifle can also be used with any rimfire, such as a 22 mag or 17 HMR, correct?

(2) It appears (if I read your data correctly) that the SAS Tolerance gives the quietest and the most repeated level from one shot to another, specifically from the first shot to the others. Am I reading that correctly? If so, then I would assume the SAS Tolerance suppressor rated the best of all? Does this suppressor allow for taking it apart and cleaning?

(3) With the Sparrow, you mention "very repeatable FFP." What is FFP? It appears the Sparrow has a louder first shot and then the others subsequent shots settle down after that. Is that what is considered "first shot pop" that I have read in other posts, or is that a different subject?

I appreciate your thoughts.




When it cones to rimfire cans, whatever brand you choose, MAKE SURE its user serviceable, especially if you plan on shooting it much. Rimfires are notoriously dirty, leaving lead and powder fouling.

Another thing you need to consider is construction material. If your only using it on rimfires and won't shoot it a ton, aluminum works. If you intend to shoot it a lot you may want to spring for a stainless or titanium can.

FRP (first round pop)is another thing that is very prevalent in rimfire cans. Some are terrible and some do a much better job at reducing/eliminating it.
 
Last edited:
Ranger walker, I would like to see you get your hands on a Dead Air 22 mask. I shot one next to a sparrow and I definitely noticed the difference just by ear, no mics.
 
Originally Posted By: crittr gittrRanger walker, I would like to see you get your hands on a Dead Air 22 mask. I shot one next to a sparrow and I definitely noticed the difference just by ear, no mics.

Let me see what i can do.
 
Originally Posted By: Kino MAnother thing you need to consider is construction material. If your only using it on rimfires and won't shoot it a ton, aluminum works. If you intend to shoot it a lot you may want to spring for a stainless or titanium can.I will never purchase an Aluminum rimfire suppressor.
 
Originally Posted By: crittr gittrRanger walker, I would like to see you get your hands on a Dead Air 22 mask. I shot one next to a sparrow and I definitely noticed the difference just by ear, no mics.

The dead air mask kicks @#$ it will be the next one I purchass when I get out of the dog house.
smile.gif


I agree with cbass16 there is no reason EVER to purchass a aluminum 22 suppresser.
 
Originally Posted By: 3DHUSKEROriginally Posted By: crittr gittrRanger walker, I would like to see you get your hands on a Dead Air 22 mask. I shot one next to a sparrow and I definitely noticed the difference just by ear, no mics.

The dead air mask kicks @#$ it will be the next one I purchass when I get out of the dog house.
smile.gif


I agree with cbass16 there is no reason EVER to purchass a aluminum 22 suppresser.

That's a pretty strong statement. I have more then 10K on my first Sparrow. It is the Aluminum design. Plus i've only cleaned it once. Yes there are several other options out there SS, TI. However for the value shopper a AL 22LR is not a bad choice. I will also say that my Sparrow has seen more then the average use, A Lot more in the 6 yrs I have had it.

Some of the new Al 22 LR have a hardcoat anodized baffles that help with cleaning and life of the suppressor.

For A true all purpose rime fire look to TI or SS.

If i can get a Dead Air 22 demo i'll post up metered results.
 
Originally Posted By: cbass16Originally Posted By: Kino MAnother thing you need to consider is construction material. If your only using it on rimfires and won't shoot it a ton, aluminum works. If you intend to shoot it a lot you may want to spring for a stainless or titanium can.I will never purchase an Aluminum rimfire suppressor.



Cbass have you guys seen the al cans giving issues? Only thing I've heard of is the AAC aluminum can blowing the threaded ends out of a couple. Not sure if it was manufacturer defect, or guys using them on centerfire rifles and then wondering why they ended up with parts laying down range. They have a lifetime warranty, but AAC isn't exactly fast at returning things I heard.
 
I was wondering the same thing. Cbass and 3Dhusker what issues have you had or seen with aluminum?

Aluminum is structurally strong enough to easily handle the pressure of rimfires and most centerfire pistols. Aluminum offers an economical option and works great for many shooters needs and shooting regimines. I've shot thousands of rounds as well through them with zero issues and to me the biggest drawback is you can't use the "dip" to clean up with.
 


Write your reply...
Back
Top